1974 LOOPCO 54 Slitters & Slitting Lines | Michael Meyer
Overview
Type:
Slitters & Slitting Lines
Manufacturer:
LOOPCO
Model:
54
Year:
1974
Stock #:
1017
Status:
For Sale
Description

16" ID's In & Out. 1-9" & 1-6" Slitter Heads

Specifications
Max Width54"
Max Thickness0.25"

Entry Coil Car: Revolvator 40,000# Capacity 60" wide Bed 72" O.D. Capacity (2) - 5" bore hydraulic lift cylinders Lift: Approx. 16" Self-contained hydraulics 3 HP AC motor Each axle individually driven by hyd. motors Pushbutton control Approx. 12" from floor to bottom of "V" cradle Removable 5" high riser on bed Overall size: 90" L x 64" W x 89" High -Uncoiler: 20" - 24" I.D. Hydraulic Expansion Pumpkin Tooth Mandrel 54.5" Face Mandrel Powered Holddown Roll w/Rubber Covered Roll AC Motor Threading Drive w/Air Clutch Sliding Base Wichita Water Cooled Brake Water Cooler for Brake Passline: 40" from Floor to Center of Mandrel Overall Size: 150" L x 74" W x 93" High -Entry Unit: Threading Table Pinch Rolls, 8" Dia. x 56.5" Face Rolls, Idler Type Side Guides, Manual Adj. Passline: 47" Overall Size: 84" L x 50" W x 75" High -Crop Shear: 58" Long Blade Hydra-Mechanical Upcut Type 10" Bore Hydraulic Cylinder Entry Passline Roll Spring Loaded Holddown Passline: 49" Overall Size: 109" L x 35" W x 81" High -(2) Slitter Heads: Crane Type Removable Heads Single Eccentric Arbor Adjustment (1) - 9" Dia. x 55" Face Arbors Entry Table (1) - 6" Dia. x 55" Face Arbors Entry Side Guides, Manual Adj. Entry Passline Rolls, 4" Dia. x 59.75" Long 75 HP DC Motor, 500/2000 RPM, 500 V, w/Blower 30 HP AC Motor Threading Drive, 1760 RPM, 230/460 V Alten Reducer w/1.837:1 Ratio Overall Size: 9" Head: 128" L x 57" W x 81" High, 15,000 Lbs. 6" Head: 122" L x 50" W x 69" High, 10,000 Lbs. Drive: 150" L x 46" W x 47" High, 7,500 Lbs. -(2) Scrap Winders: Approx. 25" W x 26" Dia. Scrap Ball Capacity Hydraulic Motor Driven Self-Contained Hydraulic Power Unit 15 HP AC Motor, 1760 RPM, 230/460V Overall Size: 84" L x 52" W x 49" High (Each Winder) -Pit Cross Over Table: -Tension Stand: Stamco Clam Shell Design Hydraulic Cylinder Open / Close Entry Separator Tooling Bar (Not attached to Frame) Exit Passline Rolls - Rubber Covered Top Roll - 66" Face x 14" Dia. Bottom Roll - 62" Face x 6" Dia., Driven for Threading by Hyd. Motor (2) Sets of New Pressure Boards (Less Felt/Carpet Covering) Air Bag Included Machine No. 4461 Overall Size: 106" L x 39" W x 53" High -Free Standing Overarm Separator: Deflector Roll Threading Table to Recoiler -Recoiler: 16" Dia. x 58" Face Drum 20" Dia. Bolt On Pad 22" Dia. x 57" Face Spare Drum Hydraulic Clamp and Expansion 12" Dia. Main Shaft Hydraulic Pushoff Lufkin (2) Speed Gear Box w/10.6:1 and 31.7:1 Ratios 200 HP DC Motor, 500/2000 RPM, 500 V w/Blower Air Operated Holding Brake Passline: 40" from Floor to Center of Drum Overall Size: 180" L x 102" W x 92" High -Hydraulic Power Unit: -Electrical Panel: Eurotherm DC Drive: -Misc. Tooling Included.

52" x 40,000 LB Loopco Slitting Line

52" x 40,000 LB Loopco Slitting Line
Slitters & Slitting Lines